Whether contractors are constructing a highway, residential driveway, private road, or parking lot, their goal is to craft a drivable surface that is capable of supporting the expected loads. It is also important to minimize the need for frequent repairs, especially if those repairs tend to be expensive. Experienced paving contractors understand the connection between a high-quality driving surface and the foundation on which it rests. Therefore, contractors will typically use road base material to achieve the best results.

What Is Road Base Material?

As its name suggests, road base is the foundation layer that lies between the soil and the driving surface. There are many materials that can be used during a road base installation, but they are all a type of aggregate. Normally, the type of road base material used will depend on its local availability and cost. Typically, road base in Austin consists of decomposed granite, gravel, limestone, river rock, or recycled concrete that has been crushed to create properly sized particles. The largest particles of road base rock are slightly less than half an inch, while the smallest particles, known as fines, are a powdery dust.

What Is the Process for Installing Road Base Material?

The first step in a road base installation is to prepare the subgrade, which is the soil on which the road base rock will rest.

1. An Austin road base installer will need to carefully consider drainage issues, then establish what the slope needs to be. Most of the time, this will involve a virtually invisible center crown so that water flows evenly to both sides.
2. The subgrade will be compacted so that it will provide a stable platform for the road base rock. If the soil cannot be adequately compacted, it may be necessary for an Austin road base contractor to excavate a little of the native soil and replace it with something more suitable.
3. Once the subgrade has been prepared, the next step is the road base spreading operation. Depending on the expected traffic, road base in Austin is normally between four and six inches in depth. Therefore, most contractors will use a backhoe or skid steer to make road base spreading faster and less labor intensive.
4. After spreading and leveling the road base material, it will be thoroughly compacted with a compactor or roller.
5. Following compaction, road base in Austin should be watered down and allowed to dry for a minimum of 48 hours. This greatly enhances the water-shedding ability of Austin road base.
6. On some projects, contractors recommend topping the road base with a weed guard. This can help prevent traffic from pumping the fines in the material to the surface under wet conditions.
7. The final step in a road base installation is normally to top it with a layer of crushed rock. The depth of this finishing layer is usually at least two inches, but it may be four inches or more.

If you would like to learn more about road base in Austin, reach out to the experts at Juniors Materials. For more than 10 years, we have been providing our customers with road base installation, dump truck hauling, decomposed granite delivery, landscape material delivery, trash pickup, and dump truck hauling needs. We are also water and soil sinking, grading, and skid-steer loader contractors. We have an exceptional reputation for dependability, responsiveness, professionalism, and workmanship. You can contact us for a free quote by either calling 512-924-6887 or submitting the online form.

Construction in the Austin metropolitan area is booming. In 2023, the area ranked seventh nationwide for new home construction, and the multifamily housing and commercial sectors are also growing rapidly. Much of the growth is fueled by an influx of tech companies, most of which continue to expand after establishing themselves in their new surroundings. Regardless of whether a construction project involves building a new home, an addition, a parking area, or even landscaping, the services of a reputable, experienced land level grading company can help ensure long-term satisfaction with the results. However, you need to make sure that the company you choose has the expertise, skills, and equipment to perform the job correctly.

What Does a Land Level Grading Company Do?

You might think that the services of a grading company in Austin are only needed once the project is substantially complete, but this is not the case. Typically, a grading company will clear the site to remove unwanted vegetation, and, depending on the project, some excavations may need to be performed. Sometimes, grading companies in Austin must also amend or stabilize the soil before performing a preliminary grade to establish the basic slope. Level grading is the process of ensuring that the land that will lie beneath the new structure is even, properly compacted, and smooth.

What Types of Building Projects May Require the Services of a Land Level Grading Company?

Level grading is essential for all types of foundations. Homes, brick or stone fences, dumpster pads, walls, garages, patios, walkways, and commercial buildings all rely on a level, strong foundation. It does not matter whether the project will be paved with concrete, brick, asphalt, or stone.

What Are the Benefits of Having a Grading Company Level the Site?

When you hire a trustworthy Austin grading company to level your site, you can receive all of the following benefits.

1. About the last thing you need is a pavement with a seriously uneven slope. Water will pool in places, and this can potentially damage your paving material. It can also pose a safety hazard as well as reduce your ability to enjoy using your pavement.
2. When it comes to foundations, the consequences of not hiring a competent land level grading company can be even more dire. Experienced grading companies in Austin have witnessed stone fences that have collapsed into a pile of rubble because of stress caused by an uneven foundation.
3. Regardless of whether you are adding a garage, building a new home, or landscaping your property, you want to ensure that water drains away from it. An experienced Austin grading company knows how to ensure that the soil is perfectly level while simultaneously ensuring that the adjacent terrain has the proper slope.
4. Hiring a grading company in Austin to level your site can help prevent soil erosion. This is important for all projects, but it is especially critical for landscaping projects.

When you need a land level grading company in the Austin area, you can count on Juniors Materials for exemplary work and service at a reasonable price. We also offer road base installation, landscape materials and decomposed granite deliveries, trash pickup, and dump truck hauling. Furthermore, we are a qualified water and soil sinking contractor and skid-steer loader contractor. To receive a free quote, you can contact us by completing our online form, or you can call us at 512-924-6887.

Whether you are planning a commercial landscaping project, a new driveway, or a garden path, you will find a wide variety of materials from which to choose. However, there are several benefits to choosing decomposed granite in Central Texas for your project.

What Is Decomposed Granite?

As you probably know, granite is an extremely strong, durable rock. However, even granite cannot withstand the relentless forces of nature forever. Decomposed granite is naturally weathered granite that has been reduced to small pieces by erosion. There are three basic types of decomposed granite in Austin.

1. Untreated or natural granite will continue to decompose after it is spread, so this is the type that is commonly used for mulching.
2. Adding resin to the granite creates a material that is highly durable and stable, so this type is the best choice for driveways and private roads.
3. Stabilized granite is less susceptible to water erosion and is harder than natural granite. It is often used for patios, walking trails, or garden paths.

What Are the Benefits of Using Decomposed Granite in Central Texas?

Although the precise benefits can depend on the nature of your project, there are several general benefits to using decomposed granite in Austin.

1. Quarries in five states produce almost two-thirds of the nation’s granite, and those five states are Texas, Indiana, Massachusetts, Georgia, and Wisconsin. Much of the decomposed granite Austin Texas property owners use is actually sourced from quarries in the Texas Hill Country. Granite is a heavy rock that can cost a great deal to transport over long distances. By sourcing the material from a local decomposed granite company, transportation costs can be reduced, resulting in a more economical price for the material.
2. Texas decomposed granite can vary in color. Most untreated Austin decomposed granite is tan or brown, but the exact hue can range from pale to dark. However, granite can be gold, green, pink, blue, gray, red, or black. It all depends on where the granite was quarried.
3. Compacted Austin decomposed granite is permeable. Thus, more water will percolate through it, which helps prevent pools of standing water while simultaneously nurturing the underlying soil and returning more rainfall to the water table.
4. Decomposed granite in Austin requires very little maintenance. If a layer becomes eroded by runoff or weathering, all you need to do is add more and compact it.
5. Last but not least, decomposed granite is an aesthetically pleasing material that can be used alone or with other materials to create a unique look. Its versatility means that you can use it to create a focal point, add a contrasting touch, or blend with your structure’s exterior as easily as you can create a vast, open expanse.

To learn more, contact Junior’s Materials, a well-respected, experienced local company. In addition to decomposed granite delivery, we also offer landscape materials delivery, trash pickup, and dump truck hauling. Furthermore, we offer road base installation, and grading services, and we are a skid-steer loader contractor as well as a water and soil sinking contractor. We have earned considerable praise for our willingness to go the extra mile, but we are equally known for our competitive prices, high-quality work, and dependability. To request a free quote, fill out the online form, or call us at 512-924-6887.

Most people are familiar with the basic concept of mulching their flower beds and vegetable gardens. However, not everyone understands how much trees can benefit from mulch in Austin, Texas.

What Is Mulch in Austin, Texas?

In basic terms, mulch is some type of chipped or ground material that can be used to cover the ground around plants. In some parts of the country, recycled tires, gravel, and furnace slag are often referred to as mulch. However, when people talk about mulch in Central Texas, they are typically referring to recycled plant matter or partially decomposed wood.

When and How Should I Apply Mulch in Austin, Texas?

As for when to mulch in Texas, the best time to mulch established trees is late spring or early winter. Seedlings may benefit from mulching prior to the onset of freezing temperatures, so be sure to schedule your mulch delivery in Austin accordingly. The best way to apply mulch is by using a shovel or rake to spread it in an even layer around your tree. The mulch should be between two and four inches deep, but it must not be in contact with the trunk of the tree.

What Are the Benefits of Mulching in Texas, Especially for Trees?

Strong, healthy trees have healthy roots that collect natural resources, including water and nutrients, from the soil. Virtually all species of trees do best when their root systems extend deep into the soil.

1. Mulching in Texas can help prevent rain from washing away the soil over the tree’s roots.
2. In the summer, the sun can raise the temperature of bare soil to more than 100 degrees Fahrenheit. Mulch in Austin can keep the temperature of the soil much cooler, which helps prevent damage to a tree’s roots.
3. In the winter, mulch in Central Texas can act as a blanket to prevent tree roots from freezing.
4. Mulching in Texas also helps conserve water. Shielding a tree’s roots from direct sunlight and reducing the temperature can reduce the amount of water lost through evaporation.
5. If you ask your mulch delivery company for organic matter, the mulch will break down over time. This adds vital nutrients to the soil that your trees can use for healthy growth.
6. Tree roots need air pockets in the soil to efficiently collect vital resources. Mulch can create these air spaces by breaking apart and loosening hard, dense soil.
7. Weeds and other plants growing in close proximity to your tree could steal its water and nutrients. Mulch can prevent vagabond seeds from sprouting by blocking the sunlight they need to germinate.

If you need landscaping materials or mulch delivery in Austin, turn to Junior’s Materials. For more than 15 years, we have been proud to provide local homeowners, businesses, and contractors with prompt, dependable service. In addition to delivering mulch in Austin, we also deliver decomposed granite, install road base, and offer trash pickup, and dump truck hauling. Furthermore, we are qualified water and soil sinking, skid-steer loader, and grading contractors. We are known for our professionalism, responsiveness, and attention to detail. For a free quote, fill out our online form, or call us at 512-924-6887.

Austin Skid Steer Contractor

A skid steer is one of the most versatile of all the machines used in the construction industry. Skid steers come in several sizes, and there are many different attachments available for each. Therefore, an Austin skid steer contractor could provide roadwork, material handling, or landscaping services.

What Are Some Examples of Services an Austin Skid Steer Contractor Might Provide?

With the right attachments, a skilled skid steer contractor can dig a hole of virtually any size. Here are a few examples.

1. You can hire an Austin skid steer company to excavate an entire foundation for a new home, office, or other structure.
2. A skid steer contractor can excavate trenches to install pipes, drainage ditches, or underground utility lines.
3. An Austin skid steer contractor can dig a hole for a new swimming pool, cellar, or septic tank.

What Are Some Examples of Services an Austin Skid Steer Contractor Might Provide?

One area in which a skid steer in Austin really demonstrates its versatility is in the area of demolition. When fitted with the proper attachments, an experienced skid steer contractor can make short work of exterior and interior demolition projects.

1. When affixed with demolition shears, skid steers can cut through drywall, demolish flooring, or cut through exterior cladding.
2. Existing concrete and asphalt pavements can be obliterated, or the skid steer operator can grind away just the surface layers.
3. A skid steer in Austin is often used to clear a building site of trees, rocks, stumps, and brush.

What Are Some Examples of Roadwork Services an Austin Skid Steer Contractor Might Provide?

In addition to offering numerous attachments, skid steers are highly maneuverable, so they can get into places that full-sized bulldozers and other large machines cannot access.

1. Skid steers can remove rocks without leaving large trenches in their wake.
2. A skid steer in Austin is perfectly capable of backfilling and grading a site for a new road.
3. Skid steers are excellent choices for spreading and leveling road base gravel. In fact, skid steer road base projects are becoming increasingly popular among homeowners as well as road construction companies.
4. A skid steer contractor can fill in holes left behind after the removal of large boulders or trees.

What Are Some Examples of Material Handling Services an Austin Skid Steer Contractor Might Provide?

Skid steers can move loads around inside warehouses or at a job site. Here are just a few examples of their material handling capabilities.

1. With an attached fork, skid steers can move pallets of raw materials and finished goods around a factory or warehouse.
2. On a job site, a bucket attachment allows a skid steer operator to transport mulch, gravel, tools, or other supplies.
3. There is even an attachment for moving bales of hay around.

What Are Some Examples of Landscaping Services an Austin Skid Steer Contractor Might Provide?

Landscaping is yet another area in which skid steers can show their versatility as well as their capabilities. Below are just a few examples.

1. A skid steer can till the soil, or mix in fertilizer or compost.
2. You can hire a skid steer company to mow down tall grass and weeds, remove undergrowth, or take out small trees.
3. With the right attachment, a skid steer contractor can remove tree stumps by grinding them away.
4. An Austin skid steer company can grade the site or build a small berm.
5. A skid steer in Austin can also be used to excavate a koi pond, prepare the ground for the installation of pavers, or excavate a trench for the construction of a wall or fence.

To learn more about the many uses of a skid steer, get in touch with Juniors Materials. We are a qualified skid steer contractor as well as a water and soil sinking contractor and grading contractor. We also offer road base installation, decomposed granite delivery, landscape materials delivery, trash pickup, and dump truck hauling. If you would like to receive a free quote, you can fill out our online form, or you can call us at 512-924-6887.

As you might infer from its name, road base has been used for many decades as a substrate material in the construction of highways and streets. However, it has become increasingly popular to construct unpaved driveways and private roads using only road base in Austin, Texas. If the contractor follows the process correctly, road base can be an economical alternative to dirt or gravel. The process begins with the calculation of the amount of road base that will be needed for the job. The contractor first multiplies the width by the length to obtain the area of the project. The desired depth, which normally ranges between three and six inches, is then added into the equation to determine the square yards that will be required. The rest of the process involves the actual work on the construction site.

What Materials Are Common for Road Base in Austin TX?

By far, crushed limestone is the most common material used by an Austin road base company. This is due in part to Austin’s proximity to one of the most bountiful limestone quarries in the region. However, Austin road base may also contain gravel, sand, or crushed stone, and it will also contain some powdery fine particles and water.

How Does a Local Road Base Contractor Prepare the Ground for an Installation?

Before spreading road base, contractors must ensure that the ground will drain properly. If necessary, they will grade the site, and they may create a center mound to facilitate drainage to each side. The ground will then be thoroughly compacted.

How Do Contractors Spread Base in Austin TX?

The precise method depends on the scope of the project. For example, if the project is to construct a private road, road base companies may allow the truck delivering the material to slowly dump the road base as it drives down the road. Workers can then use hand tools to spread the road base evenly across the designated area. For a driveway, an Austin road base company will likely have the material dumped in one or two piles at the end of the work area. The Austin road base contractor’s crew will then spread the material. As you can see, spreading road base is frequently a labor-intensive job, but it can go much faster than you might suspect. Furthermore, if the contractor uses a skid steer for spreading and leveling the road base, this can expedite the job even further.

What Do Contractors Do After Spreading Road Base?

Most projects call for compacting the Austin road base layers as they are spread. Depending on the scope of the project, compaction may be performed by machine or manually.

How Do Contractors Level Base in Austin TX?

On most projects, road base companies level the material as they spread it. Depending on the local road base contractor, they may use laser levels or more old-school methods to ensure that the material is level and has the proper crown. Leveling road base is essential to ensure that the driveway or road will drain correctly and be less susceptible to washing out when it rains.

Would You Like to Learn More About Road Base in Austin TX?

Juniors Materials is a well-respected company serving clients throughout the greater Austin area. We offer a range of services, including Austin road base installation, dump truck hauling, decomposed granite delivery, trash pickup, and landscape materials delivery. We are also a skid-steer loader contractor, grading contractor, and water and soil sinking contractor. We have an immaculate reputation and impeccable references. If you are interested in receiving a free quote, call our office at 512-924-6887, or you can use our online form to send us your information.

If you have ever tried to fill in a depression in your yard, you know that moving dirt around is a strenuous exercise. It would be even more difficult without the right tools and equipment. However, most people who need dirt work in Austin require more than just simply filling a low spot, and few people have access to the things they would need to handle the job.

What Is Considered Dirt Work in Austin?

In the broadest sense, any job that requires moving soil from one spot to another could be considered Austin TX dirt work. A dirt work company may perform  site grading, terrain modifications, or various other services that require removing, replacing, or relocating soil.

What Tools Do Contractors Use to Perform Dirt Work in Austin?

The precise tools depend on the type of Austin TX dirt work project. For example, a dirt work grading project will virtually always require a bulldozer, and it may also require a skid-steer loader or backhoe. Residential grading contractors may need all of these machines, but very small-scale jobs may only require picks, shovels, or chainsaws.

What Projects Might an Austin TX Dirt Work Company Handle?

Dirt work companies handle many different types of projects for homeowners, rural property owners, municipalities, recreational facilities, commercial and industrial property managers, educational institutions, and healthcare facilities. Therefore, the types of projects are also quite varied. Here are just a few examples.

1. Dirt work projects can dig trenches to install underground utility lines or drainage systems.
2. Dirt work grading projects may level the ground for a garden, walkway, fence, or wall. A grading contractor in Austin may also prepare the site for the construction of a foundation. Commercial and residential grading contractors may correct drainage issues or repair erosion damage.
3. A dirt work company may employ multiple techniques when completing a single project. For example, constructing a berm, retaining wall, dam, or terrace may require grading, compacting, or amending the soil.
4. Road grading services in Austin may be used for the construction of highways, suburban streets, or urban boulevards. However, a roadway grading contractor in Austin may also install, repair, or maintain gravel driveways or rural roads.
5. A dirt work company may also bring soil, gravel, or other materials to the site. A commercial or residential client may need to add topsoil for a lawn, for instance, or the landscaping plan may call for decomposed granite pathways.

If you would like to learn more about dirt work in Austin, contact Juniors Materials. We serve residential and commercial clients with a wide range of services, including road base installation, trash pickup, and dump truck hauling. We also deliver decomposed granite and landscape materials, and we are experienced skid-steer loader contractors, water and soil sinking contractors, and grading contractors. For a free quote, you can give us a call at 512-924-6887, or you can fill out the online request form.

Road base gravel is a very popular choice for driveways and private roads in the Austin area. Compared to the alternatives, road base gravel in Central Texas is much less expensive, faster to install, and kinder to the environment. However, whether you choose gravel, asphalt, pavers, concrete, or another material for your driveway or private road, you should consider the maintenance requirements.

What Is Road Base Gravel in Central Texas?

As you might expect, road base material earned its name due to its widespread use in the construction of roadways of all types. Many different materials can be crushed to produce Central Texas road base, including recycled concrete. However, the most popular is limestone gravel road base material in Austin and its surrounding area. The Austin area is situated near a major source of high-quality limestone, and this helps keep the cost of Central Texas road base delivery at an economical level.

How Do Contractors Construct a Central Texas Road Base Driveway?

Before the road base gravel delivery, contractors prepare the site. This may involve removing unwanted vegetation and grading the site to create a center slope that facilitates proper drainage, but it should always include soil compaction. If the soil cannot be sufficiently compacted, the contractor may need to remove and replace a specific depth of material. The rest of the road base driveway construction is quite straightforward.

1. The size of the gravel road base material in Austin is critical. Typically, the size of the particles in an average road base gravel delivery will range between 1.5 and 2.5 inches, but there will also be fine particles that are more akin to dust.
2. Depending on the design specifications, your road base driveway could have a total thickness of up to 10 inches. However, the average Central Texas road base driveway is closer to eight inches in thickness. The contractor may need to schedule more than one Central Texas road base delivery to achieve the proper thickness. As each base gravel delivery arrives, workers will spread and compact the material.
3. To finish the construction, contractors will normally spray the road base material with water to weigh down the fine particles. This helps prevent dust clouds from forming when traffic travels on the road or driveway.

How Should Road Base Gravel in Central Texas Be Maintained?

Gravel road base material in Austin is not as difficult to maintain as it is in parts of the country that receive heavy annual snowfalls or extended subzero temperatures. There is really very little you need to do to maintain your road base driveway.

1. Spray it down occasionally. Over time, the weight of vehicles can crush gravel into dust. The dust can get all over a vehicle, including its windshield and other glass. A garden hose is normally all you need to wet down your road base material.
2. Purchase a heavy-duty gravel rake to use on your road base driveway. These rakes allow you to remove debris that has become trapped in your gravel. However, raking also lets you level the surface and fill in small ruts or bear spots.
3. Request a base gravel delivery every 12 to 18 months. A fresh layer can repair damage, solve drainage problems, or replace any road base material that has been lost.

If you are interested in a road base gravel delivery in the Austin metropolitan area, contact Juniors Materials. We also deliver landscape materials and decomposed granite, and we offer dump truck hauling and trash pickup. Furthermore, we are experienced, qualified skid-steer loader contractors, grading contractors, and water and soil sinking contractors. We have an exceptional reputation for our professionalism, service, and integrity. To request a free consultation or quote, complete our online form. If you prefer, you can call our office in Hutto at 512-924-6887.

Over the centuries, limestone has been prized as a building material due to its strength, low thermal expansion, versatility, and durability. It is also a key ingredient in concrete. As a crushed stone aggregate, limestone is commonly used for landscaping projects and as a road base material. Limestone delivery is definitely available in Austin, and it is typically fast and economical due primarily to Austin’s proximity to the Edwards Plateau.

What Is the Connection Between Fast and Economical Limestone Delivery and the Edwards Plateau?

If you take a map and connect the cities of Austin, San Angelo, Del Rio, and San Antonio, you will have a rough outline of the Edwards Plateau. All or part of 41 counties in Texas lie within this geographic region, and the Texas Hill Country occupies the southeast part of the Edwards Plateau. Approximately 100 million years ago, an ocean covered the area, forming marine deposits of limestone, sandstone, dolomite, and shale. Geological forces uplifted the area that is now known as the Edwards Plateau. The formation of the Edwards Plateau is also connected to the formation of the Balcones Fault. The limestone in the Edwards Plateau region is of high quality, and it is relatively easy to access. Since it is not necessary to transport the material over a great distance, limestone delivery in Austin is more economical than what a limestone delivery company in other parts of the nation might charge.

What Are Some Types of Projects That Might Require Limestone Delivery?

Because limestone is such a versatile material, there are many projects that could potentially require an Austin limestone delivery. Here are just a few.

1. Limestone for Driveways: Limestone driveways are more aesthetic and less expensive than gravel or asphalt driveways, especially if the driveway is a long one. Limestone driveways deliver the benefits of gravel driveways, including permeability, and they are not as affected by weather conditions as asphalt driveways.
2. Drainage Ditches: A drainage ditch can prevent water from collecting around your home’s exterior, especially in situations involving a heavy runoff. Drainage ditches are commonly lined with crushed stone or gravel to prevent soil erosion, and limestone is an excellent material for this purpose.
3. Soil Enrichment: Crushed limestone is an excellent way to control the alkalinity or acidity of soil. It is also rich in nutrients that can boost the growth of vegetables, grass, flowers, and other plants.
4. Garden Paths: Footpaths can add a professional finishing touch to gardens or backyards. Whether you want to add character with a winding path or have a network of paths throughout your acreage, a limestone delivery company can provide you with an attractive, economical material. Depending on the scope of your project, you might be able to do most of the work yourself. To create your path, simply remove a sufficient depth of sod, cover the ground with landscape fabric, and then spread the crushed limestone.

Whether you need a delivery of limestone for driveways, garden paths, or other projects, Juniors Materials can help. In addition to delivering landscaping materials, we also offer many other services, including decomposed granite delivery, road base installation, dump truck hauling, and trash pickup. Furthermore, we are an experienced skid-steer loader contractor, water and soil sinking contractor, and grading contractor. We are known for our dependability, professionalism, and integrity. If you would like to request a free consultation or a free quote, submit our online form. If you prefer, you can reach us by phone at 512-924-6887.

A dirt driveway may be an inexpensive choice, but it may not be the best option in Austin. When it rains, your driveway can turn into a muddy area that is rutted and unsightly. Furthermore, you or your visitors may find it impossible to get their cars out of the driveway once the tires become mired in the mud. The tires on vehicles can sling mud everywhere, including the sides and headlights of the cars, and the undercarriage can become caked with dried mud. Slogging through the mud on foot can be hazardous and messy, and there is a good chance that mud will be tracked onto your steps and inside your home. Many people want to eliminate the problems with a dirt driveway, but they assume that a solution will be too expensive. Fortunately, road base in Austin, TX can be an economical, attractive solution.

What Is Road Base in Austin, TX?

As you might suspect, road base gets its name from its widespread use in the construction of roadways. Typically, paving contractors install a layer of crushed road base on top of the subgrade after preparing and compacting the soil to create a level, stable surface. The road base material in Austin is then compacted to create a durable, strong surface. Depending on your preferences, driveway road base can be left as it is, or it can be topped with an asphalt pavement. Either way, a road base driveway can solve the problems created by muddy driveways without spending a lot of money.

What Materials Are Used for Road Base in Austin, TX?

There are several types of road base material for driveways available. Crushed rock and gravel are typically the least expensive driveway road base materials available. Crushed concrete, asphalt, and other engineered materials generally cost more, but they often require fewer repairs and less maintenance, which can typically offset their initial cost.

Is a Road Base Driveway Easy to Install?

Installing road base material in Austin is not a complicated process for an experienced road base driveway professional. However, an inexperienced or unscrupulous contractor can leave customers wishing they could have their muddy driveways back as well as the money they spent on their road base driveways.

1. Crushed road base must consist of particles that are correctly sized so that it will not be exorbitantly expensive to create a surface on top of the mud. Depending on the depth of the mud, the particles may need to be as large as 2.5 inches or as small as 1.5 inches.
2. Proper compaction of the subgrade and the road base material for driveway construction is critical. Without proper compaction, a road base driveway can lack the strength and stability to support traffic, leading to ruts and washouts.
3. Like an asphalt or concrete driveway, a driveway constructed with road base material in Austin must have adequate drainage. Experienced contractors understand the finer points of grading a road base driveway. Furthermore, they understand the size and type of road base material for driveway construction can affect how efficiently the driveway will drain.

Juniors Materials has been serving customers in the Austin area for more than 15 years. Our services include the installation of road base driveways, grading, trash pickup, and dump truck hauling. We also deliver decomposed granite and landscape materials, and we are qualified water and soil sinking contractors and skid-steer loader contractors. We are known for our can-do attitude, exceptional work, and professional service. For a free quote, you can complete our online form, or you can call 512-924-6887.